Black & Decker BDPS600 Manuale delle Istruzioni Scaricare il pdf (Pagina 34)

34 • ENGLISH

f Maintain smooth and consistent speed which will help

avoid inconsistencies. Begin spraying after the pass

has begun and release trigger before stopping the

pass.

f Avoid spraying too heavily in any one area. Several

lighter coats are better than one heavy coat which can

lead to running and dripping. Remember that the flow

control knob regulates the amount of liquid that can

be sprayed. Turning the flow knob counterclockwise

increases the flow of liquid. Turning the knob

clockwise decreases the flow of liquid. If runs or drips

do occur, have a dry paint brush on hand to smooth

them out.

Warning!: ELECTRIC SHOCK HAZARD. When

spraying overhead, never tip the sprayer more than 45

degrees. The material being sprayed could leak into the

motor housing.

Tip: If the atomizer valve is not seated properly, spray

material will leak from behind the spray nozzle. If

material is leaking, turn off and unplug sprayer from

power source immediately. Follow these steps to

correct the problem:

f Unplug the sprayer from the power source. Follow

steps for “How to Use the Quick Clean System” on

page 13.

If problem presists:

f Check that the sprayer is unplugged from the

power source. Remove the spray nozzle by turning

counterclockwise (Fig. N). For the fan nozzle,

remember to push and turn counterclockwise to

remove.

f Remove the atomizer and check to see if it needs to

be cleaned or replaced. Also check inside the pump

housing for any debris or obstruction and clean if

necessary (Fig. N1).

f Replace the atomizer valve making sure it seats

properly (Fig N2).

f Thread the spray nozzle back onto the sprayer by

turning clockwise (Fig. N3).

CLEANING

Warning!:Be sure to use appropriate protective gear.

f Make sure clean up area is well ventilated and free of

flammable vapors.

f Always spray outdoors when spraying cleaning

solution through sprayer.

f Use drop cloths during pouring, mixing, and viscosity

testing of materials to be sprayed to protect your

floors and anything else in the spraying area that you

wish to remain untouched.

USING THE QUICK CLEAN SYSTEM

The quick clean system allows for a variety of useful

functions.

First, the system can allow you to spray water or a suitable

cleaning liquid while there is still spray material in the

main canister. This is useful when setting up your spray

pattern with the fan nozzle. You can spray water instead of

wasting spray material to view the spray pattern.

Second, the quick clean system allows you to flush the

pump assembly, the piston, the nozzle and the atomizer

valve. When spraying for long periods of time, spray

material may build up causing a deterioration of the

spray quality. It is good to flush this system with water or

cleaning liquid after every other spray material refill. It is

also important to flush the system when the sprayer will sit

for more than 15 minutes without use. Spray material can

dry on the nozzle and pump assembly and would require a

thorough cleaning. Always oil piston if sitting idle for a long

period of time. See “Reassembly Section”.

Third, the quick clean system allows for a faster O clean-

up when your project is complete. One or two flushes

through the quick clean system gives you a head start on

cleaning the nozzle, the atomizer, the pump and piston,

Please follow recommended cleaning steps in this manual

when performing a final clean of the system.

HOW TO USE THE QUICK CLEAN SYSTEM

f Unplug the sprayer from the power source.

f Fill the quick clean fill cup, to the 95ml fill line, with

water or the approprate cleaning solution.

f Open the quick clean door, and pour in the cleaning

solution as shown in Fig. O. Do not overfill the

reservoir.

f Switch the quick clean lever from paint to clean

(Fig.O1).

f Plug in the sprayer.

f Spray into a waste container, cardboard box or test

surface to completely flush the sprayer system.

f Once the spray pattern turns to only the color of the

cleaning solution, begin cleaning.

f You may need to flush more than once.

NOTICE: Please note, this is not the final cleaning

step.

TO BEGIN CLEANING:

f Unplug the sprayer from the power source.

f Unscrew the lid from the side of the canister and pour

any remaining liquid back into the original container

(Fig. P).

f Pour a small amount of the appropriate cleaning

solution into the canister (Fig. P1).

f Warm soapy water for water based materials

f Manufacturers recommended cleaning solution for oil

based materials

f Replace the lid on the canister securely and

vigorously shake the sprayer.

1 2 ... 29 30 31 32 33 34 35 36 37 38

Commenti su questo manuale

Nessun commento

Black & Decker BDPS600 Manuale delle Istruzioni Pagina 34

Commenti su questo manuale

Prodotti e manuali riguardandi Spruzzatori per vernici Black & Decker BDPS600